Jumat, 15 Maret 2019

IOD SYSTEM

IOD SYSTEM

IOD (Intermittent Operating Device)
Is a device that is installed on the back of the ZVT chassis that can change the pattern and direction of the gear. Moves based on the rear axle axle rotation of the gear that rotates the inside of the IOD and IOD DISC so that it pushes the trigger which finally moves the ARM on the rear wheel side gear.

IOD Single Unit has an arm that is located on one side of the gear either LEFT (Left) or RIGHT (Right) so the motion pattern of the gear will be affected on the position of the arm.

The IOD Double Unit has a pair of arms located on both sides of the rear gear so that it increases gear capability when the two arms move alternately.

DISC IOD : An IOD movement trigger indicates how many movements in one disc rotation there are
Single Unit: S1 Single turn, D1 Double turn and T1 Triple turn

Double Unit: W1 Left, W2 Right and D2 Left Right

ARM
an arm that is located between the chassis and rear gear wheel that is connected to the IOD motion mechanism. The arm will move according to the IOD Disc rotation which pushes the trigger so that the arm will move downward so the gear can turn in the direction that matches the IOD.

(Source : http://nikonih.blogspot.com/2015/04/crush-gear-iod-system.html)

CRUSH GEAR CHASSIS

CRUSH GEAR CHASSIS

There are 6 types of chassis in the Crush Gear series

V1: The chassis of the original Crush Gear was produced with 1 bolt hole in the batterybox so there is no need to worry "thinking about setting a spin or dash. The rear chassis is not universal so not all rear bumpers / rear weapons can be mounted on the chassis can be installed.

VT: a.k.a Variable Transmuting is a development of chassis V1 where there are 4 holes in the batterybox so we can set our Crush Gear as we wish. first hole from front for spin, second for normal, third for semi-dash, and fourth for full-dash. Unlike V1, VT Chassis has universal rear so that any rear bumpers and rear weapons (except rear bumper V1) can be attached to this chassis, including IOD.

MVT / N: more sophisticated than VT where the battery box can be set / shifted without having to remove the bolt. consists of 4 parts, the main part of the chassis, battery box, dynamo cover, and gearset cover. so with this chassis if you want to remove the dynamo, just open the cover dynamo. or want to check the gearset just by removing the wheel and gearset cover. can be obtained from CG: Wild Haken, Gallop Horn, Breakdeath Schyte, and Geo Scorpio. This chassis has also been produced in aftermarket part in white form.

MVT / D: special chassis with a height from the bottom of the chassis to the top of the chassis is lower "5mm” from the other chassis type. We can call it" flatter "only, the batterybox part cannot be varied like the MVT / N or VT chassis. from 4 chassis parts such as MVT / N, suitable for dash settings, can be obtained from CG: Mega Dash Striker, Hidlander, Ark Cavalier, and Rushing Edge.

MVT / S: Special chassis with rear wheel hole higher than front wheel hole allowing the chassis to remain parallel to the ground when using large diameter wheel spin behind. because of this, the use of a normal diameter wheel is not recommended to be put behind because the wheel will not touch the ground. MVT / S also consists of 4 chassis parts. suitable for spin settings. This chassis can be obtained from CG: Mega Spin Lefter, Vort Granade, Beat Impulse, and Senki Gai-Oh.

ZVT / N / S: The chassis is up to date with the combined spec of MVT / N and MVT / S where we can set this chassis into normal mode by using a normal cover and pin to Normal (N) or spin mode by using spin cover and switchpin to spin (S). can be obtained from all CG series Nitro.

(source: https://www.facebook.com/notes/gear-fight-indonesia/chassis-type/226192087530535)

Battle Gear Auldey

18.07 Battle Gear No comments

Battle Gear Auldey

In 2002 auldey also produced battle cars Which Called Battle Gear. Some Battle Gear have a look like Crush Gear. Battle Gear bodies is bigger than Crush Gear

Types of Battle Gear

1. Dragon Blaze

2. Phoenix (Its Looks like Grifeed on CG)

3. Thunder Break (Its Looks Like Dino Spartan on CG)

4. Crab Killer (The Front Weapon Looks Like Dino Phalanx on CG)

5. Ghost

6. Giant Elephant

7. Shark Hunter

8. Hurricane

9. Swordsman (Its Looks Like Stealth Jiraiya On CG)

10. Evilteeth

11. King Lion

(Source : Google Image, Writers opinion)

BREAK GO GA

17.23 Break Go Ga No comments

Break go ga is a battlecar which produced by Bandai in 2018. This toy is predicted to become the successor to Crush Gear which was booming in 2001-2005 . Promotional video appeared in 2018 but the video was discontinued . There are differences between Crush Gear and Break Go Ga .Break Go Ga body is smaller than Crush Gear but with a larger weapon. Crush Gear uses rpm in its weapon while Break Go Ga uses torque. Break Go ga Doesn't Have Rear weapon Like Crush Gear.

Types of Break go ga